I have been busy lately so I thought I would combine the AARs for two activations into one report. These went very fast, well, one of them did. the other did last a coupe of hours and involved me doing something very new for me…FT8…just not with the Penntek TR35. It was used to make CW contacts at the first activation.
The first park I went to was my hometown park K-2169 Cloudland Canyon State Park. This is my go to park when I don’t have a lot of time. I also can go to the Sittons Gulch parking area which is much closer than the top of the mountain by a solid 15 minutes of driving. Well, this is where I went and during the week, I can also get to choose my parking space most of the time too. Today proved a little tough but it worked out. When I got to the park there were a few cars already there and they were literally in all the places I like to setup, save one… So luckily for me there was a space in a corner like I prefer to use as it gives me room to deploy my counterpoise wires and not have to worry about people tripping over them.
I also only deployed a single counterpoise element today as well. I was curious if it would heavily affect my ability to make contacts with only a single radial, but it didn’t seem to matter much on this day. Due to my spot, I was able to run it straight away from the truck too for what that is worth. Seems that if I don’t use a radial at all, the hamstick will use the coax and the truck body for the counter poise and I will have about a 1.8:1 SWR on the nanoVNA, but if I simply add once tuned radial, it drops to 1.2:1 and if I add two it is pretty much 1:1 SWR. This is why I always deploy at least one if there is time at all, it helps with my transmission pretty dramatically. I found this chart online and used it as a reference to see what would be the results of better antenna SWR and as you can see, at 1.8:1 you lose almost 10% of your energy and at 1.2:1 you only lose about 1%. This is why I don’t worry about deploying both radials if I am in a time crunch. I also know that there are a lot of other things at play here like radiation pattern and take off angle, but it is pretty consistent since it is a ham stick every time and I cant easily change that.
Once setup I immediately jump on 20 meters to get things going today and it did not disappoint! 20 meters was alive and well on this day with a lot of activity.
Today’s weapon of choice is the Penntek TR35 Amateur Transceiver. I bought this radio last year for this reason alone and it took me a while to get around to using it as I was trying to get my IC-705 up and running at the time. I finally came around to the concept that the 705 just wasn’t for me and stopped using it. Sometimes a radio, even a wonderful machine like the 705, just isn’t the radio you want to use, so I sold it back in August. I kept this radio though as I really love the whole radio, literally the whole thing is as close to a perfect CW rig as I could get. It has every function you need on the surface that you could want and nothing you don’t need. The built in filters are really well done and it can even listen to SSB if you are into that sort of thing. The compact size also makes for another reason I like this machine, it is destined to be my new travel radio replacing the venerable Elecraft K1 that I also sold last August due to lack of use. I do want to add an antenna tuner at some point to this kit so I can use random wire antennas, but for now it has a tuned antenna in the kit.
This is the kit when setup. The Penntek TR35, the N6ARA Tinykey, a set of simple headphones (with an adapter to make it play out of both ears) and a 10 cell AA battery pack. I chose a 10 cell pack as it will give me almost 13 volts when the batteries are charged and I can use alkaline cells in a pinch by bypassing two cells with a couple of dummy cells I made in the machine shop. The kit also includes several pens, a pencil (since they don’t dry out), a Field Notes notebook, a couple of lengths of coax, one of which has a ferrite bead common mode choke built into it, a 40M EFHW antenna with an additional radial for it and a throwline with a weight, everything you could need to get the little machine on the air.
Here is another thing I like about using my truck for POTA, I can use the bedcover for a table and just spread everything out on top of it like you see in this picture. If I can operate outside I will always choose that option, but sometimes, the weather or time just prohibit that.
I had a good run with the little Penntek TR35 as you can see in the log. So if you wonder how well things can go, this is a 5 watt radio into a hamstick on my truck. It is one of the worst possible arrangements you can possibly come up with and I still ended up with almost two pages of contacts. Now if the bands are trash, then all bets are off, but you really don’t need a ton of power to do a POTA activation and have a good time. On to…
North Chickamauga Creek WMA K-3958
The next outing was in Tennessee at the North Chickamauga Creek WMA in Soddy Daisy TN. This little park has not seen a ton of activations and to prove that, just go to this parks page on the site and look at who (with only two activations mind you) in the top activator and also who holds the highest QSO count as of this writing. Yeah, it is me. There have been some people activate this park, but it just doesn’t get the attendance of places like The Great Smokey Mountains or even Cloudland Canyon State Park. I don’t understand why either, it has easy access and is pretty close to town. Maybe after I write about it and give it some notoriety it will see some more attendance…who knows?
I was here on a Friday during the mid day hours, so the park was pretty much abandoned except for me and a couple with their dog in the river bottom. I setup in a spot where I had room to deploy a radial and got the sBitx v2 out this time as it has a mode built in that the Penntek TR35 does not…well actually it has a bunch of modes that the Penntek doesn’t have, but this radio is special in that it will do FT8 natively in the radio. Yeah, no computer, no sound card, no setting up complicated software, no figuring out how to get the computer to talk to the radio and vice versa. You just choose FT8 from the mode list, dial up the frequency, set a few things like your call sign and grid locator and hit Call CQ. Now, the radio is a beta version of sorts and it has a few bugs to work out, one of them is currently in the FT8 section too, as long as I am calling CQ and a QSO ensues, the whole thing works like clockwork, but if I answer another operator’s CQ it has a glitch and wont sequence correctly. So I can use it for now, but only if I call CQ. Even so, it still works and I made almost a dozen contacts on this day with FT8, so I am happy about being able to use another mode on activations.
Here you can see a QSO has just finished with WD5BFH and the radio even logged it for me! Oh yeah, it even has a logging program running in the background to log your QSOs as well. I really like this radio.
Here we have the antenna layout for today, the single radial was really close to 45 degrees due to the slope behind the truck. That made the SWR even better and I was stoked to get on the air and see what I could find out there in radioland.
I am also testing the reserve capacity of this 8aH battery I bought last year off of Amazon, I keep turning the power up higher and higher to see if the battery can handle it and today saw me using 30 watts of power for almost two hours! I shut down the activation because of time constraints and not because of the battery so it works great for my needs.
Once again I was able to setup on the truck bed cover, and I am acutely aware that I need an easier logging process. Hand written logs are nice, but they are slow to transcribe. I am thinking that I too can come into the 21st century and use a computer to do my logging…I know, I know. I have really railed on battery powered devices, but at some point I guess I just need to bite the bullet and get a computer of some sort for logging. I am thinking of using a Linux based OS for this as these seem to be more reliable and do not update and crash all your stuff… windows, I am looking at you.
This display below is not how it looks when booted up for the sBitx V2 in the native configuration. I have scrolled it down to be able to see the top QSO in the logbook so I can confirm the QSO did in fact get logged when running FT8. The photo underneath this one is what the screen looks like when opened initially. The screen has more information than can be displayed normally so since it is a web browser layout, you simple scroll down to see the other intel. Things like the on-screen keyboard, the logbook and the macros (message memories) are what you find when you scrll down. But the way I have it here is an efficient way to run this mode for me as you can see everything you need on one screen. Sorry for the reflections, it was tough getting this frame outdoors.
This is the native layout at startup.
You can see the time stamps for the FT8 contacts are pretty spread out. This is a function of my operating skill level being low and the lack of “responding to other calls” being buggy with this mode. I know this because the band was on fire that day.
All in all I had a great couple of outings for POTA and radio in general. I hope you enjoyed these after action reports and look forward to seeing you again soon!
73
WK4DS